By ·

Motorcycle comparison · Retro Classic vs Naked Bike

Kawasaki Z 900 RS (MY2018) vs Z900 (MY2017)

Kawasaki Z 900 RS vs Z900: where they split, and which one to buy.

Push the Kawasaki Z 900 RS through a run of bends, and it'll hang with meaner-looking bikes. The Kawasaki Z900 gets fully adjustable suspension for noticeably less money. Under a heavier rider, its soft shock bottoms out.

Kawasaki Z 900 RS (MY2018) and Kawasaki Z900 (MY2017) side by side
Kawasaki Z 900 RS (MY2018) 2018–2024 · Z1 Soul, Modern Muscle Kawasaki Z900 (MY2017) 2017–2019 · Speed With Nothing Wasted

So which one do you buy?

The Z 900 RS has the edge if…

Traveling with luggage

Narrow edge: Z 900 RS

The Z 900 RS carries a touring load slightly better. The reason: a better passenger seat.

The Z900 has the edge if…

Sporty riding on twisty roads

Small edge: Z900

Once the road starts to bend, the Z900 noses ahead. Most of that is harder acceleration and more feel through the bars. Your own skill counts for more than a gap this size.

What makes each one tick

Z 900 RS

A heavier flywheel and lower compression round off the Z 900 RS's four. The throttle draws a smooth pull from the middle revs, and the engine doesn't sour when you chase the top. You're sitting tall, yet the pegs and wide bar let you shift weight into a corner. Two-up at night, it steers true.

Nils rode the Z 900 RS in Styria and Switzerland in 2018, and in Austria and Montenegro in 2024 (NastyNils Testride).

Z900

There's a howl waiting high in the Z900's revs, where its four really wakes up. It snatches at low revs. At 463 lb (210 kg), it doesn't take much push on the bar to steer the bike into a corner. On the Angeles Crest Highway, the front darts in.

Nils rode the Z900 in Switzerland in 2017, and in Spain in 2019 (NastyNils Testride).

The Voice of Experience

Portrait of NastyNils

What actually separates them

  • The Z900 has the lower seat: 31.3 in (795 mm) vs 32.9 in (835 mm).
  • The Z900 has the lower wet weight: 463 lb (210 kg) vs 474 lb (215 kg).
  • The Z900 makes more peak power: 125 hp (92 kW) vs 111 hp (82 kW).

See every difference ↓

Which one for the way you ride

A confidence-building first motorcycle

Look elsewhere

As first bikes, both are a stretch. Starting smaller isn't a step down.

On commuting and running costs, these two are a wash. That's where your budget and your inseam get the final say.

Who each one is built for

Texas Hill Country Weekend Rider

Texas Hill Country · Twisted Sisters · Circuit of The Americas

Appalachian Technical Corner Rider

Back of the Dragon · Blue Ridge Parkway · Cherohala Skyway

SoCal Canyon Performance Rider

Angeles Crest Highway · Coronado Trail Scenic Byway · Big Sur Coast Highway

What's good, and what you'll live with

Z 900 RS

Strengths

  • Torque from the basement
  • Built for long days
  • Tall-rider friendly ergonomics
  • Fully adjustable at both ends
  • Faster than it looks

Trade-offs

  • Rear shock thumps sharp hits
  • Loose through transitions
  • No quickshifter offered
  • No wind protection
  • Stock seat uncomfortable on long rides

Z900

What owners say

Strengths

  • Excellent value for money
  • Linear, exhilarating engine
  • Agile, intuitive handling
  • Good fuel economy
  • Low running costs

Trade-offs

  • Jerky throttle response at low revs
  • Cramped legroom for taller riders
  • Lacks modern electronics
  • No wind protection
  • Soft shock struggles with heavier riders

Known problems to check before you buy

Z 900 RS

  • Front tire may develop internal blistering (Sumitomo manufacturing defect) Due to a defective manufacturing process during sidewall rubber installation, the front tire may develop blistering on the inner surface. A tire with internal blistering can fail and increase crash risk. Tire supplier: Sumitomo Rubber Industries, Ltd. Non-compliant with FMVSS 119. Affects only MY2024 Z900RS ABS, Z900RS Café ABS, and Z900RS SE ABS.
  • Rear brake line and ABS wheel speed sensor cable can contact rear tire During factory assembly, the rear brake line and wheel speed sensor cable may have been incorrectly routed, allowing them to contact the rear tire. This can damage the brake line (brake fluid loss, reduced braking performance) or sever the ABS sensor cable (ABS failure, incorrect speedometer reading). Affects both Z900 and Z900RS MY2018.
  • ABS hydraulic unit contaminated with aluminum shavings The ABS hydraulic unit may have been contaminated with aluminum shavings during manufacturing (defective fixture shaving ABS pump housing). This can cause the front or rear wheel to lock up during braking despite ABS. Affects MY2019 Z900RS ABS and Z900RS Café ABS.
  • False neutrals and clunky/agricultural shift action The gearbox occasionally misses shifts, especially during quick upshifts. Most frequently reported between 5th and 6th gear, but also from neutral to 1st when departing. Downshifts are agricultural and clunky. Higher-quality engine oil and correct shift lever position can alleviate the problem. Design-inherent, not an isolated defect — known from the Z900 platform, confirmed for the Z900RS.
  • Front brake lacks sharp initial bite, spongy lever feedback Despite radial-mount four-piston Nissin calipers, the front brake lacks direct, firm initial bite. The lever feel is indirect, especially during aggressive downhill braking. Braided steel lines and higher-performance brake pads significantly improve feel. The SE model (from MY2022) with Brembo M4.32 calipers and braided steel lines resolves this issue from the factory.
  • ABS activates prematurely, especially on front brake The Nissin ABS unit activates prematurely, especially at the front brake during harder braking. The ABS is not deactivatable on any 2018–2024 model year. This reduces confidence during aggressive braking and trail braking. The ABS kicks in earlier than desired.
  • Footpegs scrape tarmac at moderate cornering speeds The lower and further-forward footpeg position (compared to Z900) combined with the factory-soft rear suspension setting (minimum preload from factory) causes the footpegs to scrape the road at moderate cornering speeds. The short feeler pegs ("Angstnippel") wear down quickly. Solution: increase rear shock preload by 3–5 turns.
  • Snatchy, on-off throttle response at low RPM (ECU mapping) The Z900RS exhibits abrupt, jerky throttle behavior at low RPM and low speeds, particularly when rolling on throttle from closed, departing from standstill, and during gentle gas application in corners. The fuel-cut programming (overrun fuel cutoff for emissions compliance) causes abrupt injection on/off behavior. The dual throttle valve system (sub-throttle servo) with cable-operated main throttle exacerbates the issue. The problem is most pronounced on MY2018–2019 models. Common remedies: ECU reflash (e.g., Ivan's Performance), throttle cable adjustment. Later model years show improvement according to multiple sources.
  • Engine revs to 2,500–4,000 rpm on cold start On cold start, the engine revs up to 2,500–4,000 rpm to bring the catalytic converter to operating temperature faster (Euro 4/5 emissions compliance). This is particularly intrusive in residential areas. It is not a defect but a deliberate ECU calibration for emissions standards. Some owners report occasional stalling during warm-up phase.
  • Clutch judder/shudder when cold during takeoff The clutch exhibits pronounced judder when cold during engagement into first gear. Multiple owners report the problem partially persists after warm-up. Some dealers consider this normal behavior. Possible remedies: soak clutch plates in oil overnight (dealer recommendation), use higher-quality engine oil. The clutch judder when cold is a widely documented complaint.

Z900

  • Rear Shock Mounting Bore Becomes Oval The mounting holes of the rear shock linkage on the frame can elongate and become oval under load when the shock absorber bottoms out. This compromises damping function and can cause riding instability. Root cause: insufficient material thickness at the linkage mounting point, combined with the stock shock absorber's tendency to bottom out when loaded.
  • Rear Brake Line and ABS Sensor Cable May Chafe Against Tire During factory assembly, the rear brake line and wheel speed sensor cable may be incorrectly routed, causing them to chafe against the rear tire. This can damage the brake line (reduced braking performance) or sever the ABS sensor cable (ABS failure).
  • ABS Hydraulic Unit Contaminated with Aluminum Shavings The ABS hydraulic unit may become contaminated with aluminum shavings during manufacturing due to a defective machining fixture that shaves the ABS pump housing. This can cause the front or rear wheel to lock up during braking.
  • Front ABS Engages Too Early The Nissin ABS unit activates prematurely, particularly on the front brake, during hard braking. The ABS cannot be disabled on 2017–2019 models. This reduces rider confidence during aggressive braking and trail-braking maneuvers. Multiple professional testers and owners confirm the issue.
  • False Neutrals, Especially Between 5th and 6th Gear The transmission occasionally misses shifts, especially during rapid upshifts above approximately 6,000 rpm. Most commonly reported between 5th and 6th gear, but also between 2nd and 3rd gear. Incomplete clutch disengagement exacerbates the problem. Downshifts are described as "clunky." Design-related, not an isolated defect.
  • Snatchy Throttle Response / Jerky low-RPM fueling The Z900 exhibits jerky, on-off throttle response at low RPMs and speeds, particularly in 1st and 2nd gear. The bike bucks and surges when holding a constant low speed. The cause is emissions-compliant ECU tuning, not a mechanical defect. The problem is exacerbated by the closed secondary throttle plates at low RPMs.
  • Ticking Noise from Timing Chain Area Audible ticking from the timing chain area, particularly noticeable because the Z900 is a naked bike. Slight ticking is considered normal (metal-to-metal contact from the automatic timing chain tensioner). In rare cases, the automatic tensioner fails and the noise becomes pronounced. The very quiet stock exhaust makes mechanical engine noises more prominent.
  • Turn Signal Bracket Rubber Inserts Become Brittle and Break The rubber inserts that hold the stock turn signals in the body become brittle and break, causing the turn signals to hang loose on their wires. Vibration and UV radiation accelerate the wear. OEM replacement turn signals also fail within 1-2 years. Affects multiple Kawasaki models, not just the Z900.
  • Handlebar Vibrations at Highway Speeds Noticeable handlebar vibrations at higher speeds cause hand numbness on longer rides. The bike's unfaired design and inline-four engine contribute to this issue. The stock handlebar is considered undersized for the motorcycle. Numerous aftermarket handlebar weight solutions are available.
  • Surface Rust on Stock Steel Fasteners Stock steel fasteners and hardware develop surface rust, especially brake caliper bolts and exposed hardware. Kawasaki uses standard steel fasteners instead of stainless steel or coated alternatives.
  • Rear brake line and ABS wheel speed sensor cable can contact rear tire During factory assembly, the rear brake line and wheel speed sensor cable may have been incorrectly routed, allowing them to contact the rear tire. This can damage the brake line (brake fluid loss, reduced braking performance) or sever the ABS sensor cable (ABS failure, incorrect speedometer reading). Affects both Z900 and Z900RS MY2018.
  • False neutrals and clunky/agricultural shift action The gearbox occasionally misses shifts, especially during quick upshifts. Most frequently reported between 5th and 6th gear, but also from neutral to 1st when departing. Downshifts are agricultural and clunky. Higher-quality engine oil and correct shift lever position can alleviate the problem. Design-inherent, not an isolated defect — known from the Z900 platform, confirmed for the Z900RS.
  • Footpegs scrape tarmac at moderate cornering speeds The lower and further-forward footpeg position (compared to Z900) combined with the factory-soft rear suspension setting (minimum preload from factory) causes the footpegs to scrape the road at moderate cornering speeds. The short feeler pegs ("Angstnippel") wear down quickly. Solution: increase rear shock preload by 3–5 turns.

What they cost used

These prices compare a 7-year-old Z 900 RS with a 7-year-old Z900.

Z 900 RS
$8,400
Z900
$7,000

At seven years old, the Kawasaki Z 900 RS sits around $8,400 while the Kawasaki Z900 lands near $7,000. That's a $1,400 gap in the Z900's favor. These figures come from earlier US market records, not live listings.

What they share

Displacement
948 cc
Engine
Inline-four
Cooling
Liquid-cooled
Fuel capacity
4.5 US gal (17 L)
Gearbox
6-speed
Final drive
Chain
Fork
Upside-down (USD)
Front tire
120/70-17
Rear tire
180/55-17

Where the spec sheets split

Seat height and weight
Z 900 RS Z900
Seat height 32.9 in (835 mm) 31.3 in (795 mm)
Wet weight 474 lb (215 kg) 463 lb (210 kg)
Engine, power and torque
Z 900 RS Z900
Power 111 hp (82 kW) 125 hp (92 kW)
Peak power at 8,500 rpm 9,500 rpm
Torque 73 lb-ft (98 Nm) 73 lb-ft (99 Nm)
Peak torque at 6,500 rpm 7,700 rpm
Top speed 139 mph (224 km/h) 149 mph (240 km/h)
Fuel economy and tank capacity
Z 900 RS Z900
Fuel economy 44 mpg (US) / 5.3 L/100 km 43 mpg (US) / 5.5 L/100 km
Other specifications
Z 900 RS Z900
Wheelbase 57.9 in (1470 mm) 57.1 in (1450 mm)

What comes fitted, what costs extra

Z 900 RS Z900
Traction Control Standard Not offered
Heated Grips Option Not offered
LED Headlight Standard Not offered

Head to head, area by area

Both bikes on the same scale, one area at a time.

Braking

Engine

Handling

Suspension

Comfort

Reliability

Practicality

Sporting Capability

Usability

Specs and equipment as of November 6, 2026. The riding calls use the same ratings behind both buyer's guides.